Page 73 - Polaris_RZR_Catalogo_Acessorios_2019

FOR THE LIFE THE KEY TO KEEPING YOUR POLARIS OFF–ROAD VEHICLE PERFORMING PARTS & GARAGE

as well as the day you brought it home is proper maintenance. Items like belts, filters, and
OF YOUR RIDE batteries represent only a few of these critical items engineered specifically by Polaris. MAINTENANCE

AIR FILTERS DRIVE BELTS OIL & LUBRICANTS

Critical to engine performance and Polaris Engineered belts deliver
reliability. A clogged air filter can restrict unmatched performance for your MAINTENANCE
air flow to the engine leading to reduced off-road vehicle. Developed and tested
engine performance. Dirt and debris on all our engines for all environments
ingestion can damage the engine leading and conditions. Check your belt for TIP
to reduced engine life or catastrophic delamination, hour glassing and glazing.
failure. Polaris recommends changing
the vehicle’s air filter at the specified MAINTENANCE
intervals outlined in the owner’s manual, BREAK-IN PERIOD
which may be shorter if your vehicle is
MAINTENANCE
subject to severe conditions.
The break-in period for your new RZR is the first
OIL FILTERS 25 hours of operation, or the time it takes to
use the first two tanks of fuel. No single action
Change oil filters with every oil change on your part is as important as a proper
to provide the best protection for your
engine. Superior engine protection break-in period. Careful treatment of a new & TRAILERING VEHICLE CARE
BRAKE PADS keeps your engine operating at peak engine will result in more efficient performance
performance. Be sure to follow the and longer life for the engine. Perform the listed
suggested service intervals for oil/oil
Check your brakes if you are close to the procedures carefully.
recommended service interval, hear filter changes.
grinding when applying the brakes, your
vehicle is taking longer to stop or if you NOTICE: Excessive heat build-up during the first three hours of
operation will damage close-fitted engine parts. Do not operate at
have to apply more pressure to your
pedal to engage the brakes. Check the full throttle or high speeds for extended periods during the first
three hours of use.
brake discs for signs of cracks,
excessive corrosion or warping. BATTERIES
If the brake pads are contaminated with Never leave a battery unattended
oils or grease (petroleum products), brake
pads have to be discarded and replaced. during the storage season. To ensure
your battery maintains its level of
Discs need to be cleaned with brake charge when unused for extended
cleaner or alcohol based cleaner only. periods of time or during freezing
weather, the battery should be
connected to a BatteryMINDer ® . Be
sure to check for corrosion from the
terminals to the ends of the cables.
MAINTENANCE SCHEDULE

25 HRS/400 km 50 HRS/800 km 100 HRS/1600 km 150 HRS/2400 km 200 HRS/3200 km 350 HRS/4020 km 500 HRS/8045 km
BREAK-IN 6 12 18 24 30 36 CHECK YOUR
OWNER'S MANUAL
MAINTENANCE FOR ADDITIONAL
MONTHS MONTHS MONTHS MONTHS MONTHS MONTHS RECOMMENDED
SERVICE ITEMS
ENGINE OIL: EXHAUST SYSTEM: ENGINE OIL: ENGINE OIL: ENGINE OIL: ENGINE OIL: ENGINE OIL: AND VEHICLE-
CHANGE INSPECT & CLEAN CHANGE CHANGE CHANGE CHANGE CHANGE
INSPECT FOR LEAKAGE OR SPECIFIC TIMING
GENERAL CARBON BUILD UP AT JOINTS DRIVE BELT: BATTERY: BRAKE PADS BATTERY: AIR FILTER:
LUBRICATION: INSPECT & CLEAN SCREEN TYPE INSPECT & ADJUST TEST, CLEAN, & & FLUID: TEST, CLEAN, & INSPECT, CLEAN
ALL FITTINGS, PIVOTS, SPARK ARRESTOR REPLACE AS NEEDED CHECK FLUID LEVEL INSPECT & CLEAN CHECK FLUID LEVEL REPLACE AS NEEDED
CABLES, ETC. REPLACE AS NEEDED REPLACE AS NEEDED REPLACE AS NEEDED
GENERAL TRANSMISSION COOLANT:
AIR FILTER: LUBRICATION: FLUID: DRIVE BELT: SPARK PLUGS: DRIVE BELT: CHECK LEVEL
INSPECT & CLEAN ALL FITTINGS, PIVOTS, CHANGE INSPECT & ADJUST INSPECT INSPECT & ADJUST REPLACE EVERY 2 YEARS
REPLACE AS NEEDED CABLES, ETC. REPLACE AS NEEDED REPLACE AS NEEDED REPLACE AS NEEDED
EXHAUST SYSTEM: GEARCASES:
EXHAUST SYSTEM: DRIVE BELT: INSPECT & CLEAN TIRES: EXHAUST SYSTEM: GENERAL CHECK OIL LEVEL
INSPECT & CLEAN INSPECT & ADJUST INSPECT FOR LEAKAGE OR INSPECT CONDITION INSPECT & CLEAN LUBRICATION:
INSPECT FOR LEAKAGE OR CARBON BUILD UP AT JOINTS & PRESSURE INSPECT FOR LEAKAGE OR ALL FITTINGS, PIVOTS, EXHAUST SYSTEM:
CARBON BUILD UP AT JOINTS REPLACE AS NEEDED CARBON BUILD UP AT JOINTS CABLES, ETC. INSPECT & CLEAN
INSPECT & CLEAN SCREEN
INSPECT & CLEAN SCREEN TYPE SPARK ARRESTOR EXHAUST SYSTEM: INSPECT & CLEAN SCREEN INSPECT FOR LEAKAGE OR
TYPE SPARK ARRESTOR INSPECT & CLEAN TYPE SPARK ARRESTOR EXHAUST SYSTEM: CARBON BUILD UP AT JOINTS
INSPECT FOR LEAKAGE OR INSPECT & CLEAN INSPECT & CLEAN SCREEN
CARBON BUILD UP AT JOINTS INSPECT FOR LEAKAGE OR TYPE SPARK ARRESTOR
CARBON BUILD UP AT JOINTS
INSPECT & CLEAN SCREEN
70
70 TYPE SPARK ARRESTOR INSPECT & CLEAN SCREEN 71
TYPE SPARK ARRESTOR