Page 54 - Sportsman Catalogo Acessorios 2022

FOR THE LIFE LIMITS WITHOUT SACRIFICING PARTS & GARAGE
PARTS THAT PUSH THE

STRENGTH AND DURABILITY.
We build our products so anyone with the
OF YOUR RIDE right tools can maintain their vehicle.

MAINTENANCE
MAINTENANCE AIR FILTER MAINTENANCE
TIP BATTERY A clogged air filter can restrict air
flow to the engine leading to
To ensure a battery maintains its reduced engine performance,
level of charge when unused for engine life or catastrophic failure.
BREAK-IN PERIOD extended periods of time or during OIL & LUBRICANTS
freezing weather, the battery
The break-in period for your new should be connected to a suitable
battery charger. Be sure to check
SPORTSMAN is the first 25 hours for corrosion from the terminals to DRIVE BELT
of operation, or the time it takes the ends of the cables.
to use the first two tanks of fuel. Polaris Engineered belts deliver unmatched performance for
No single action on your part is BRAKE PADS your off-road vehicle. Developed and tested on all our engines
as important as a proper for all environments and conditions. Check your belt for HD PARTS
break-in period. Careful Maintaining and/or replacing delamination, hour glassing and glazing.
treatment of a new engine will brakes are critical to the safety BREAK-IN PERIOD
result in more efficient and functionally of a vehicle. • Use lower gear (if available) while varying speeds and avoid
performance and longer life for Brake pads should be checked wide open throttle for 8-16 km
the engine. for wear and oil or grease • If no low gear is available, vary at moderate speeds while
(petroleum products) avoiding wide open throttle for 80 km
contamination and brake discs
NOTICE: Excessive heat build-up during the should be checked for cracks,
first three hours of operation will damage excessive corrosion or warping. SERVICE PARTS
close-fitted engine parts. Do not operate at OUR INVESTMENT YOUR ADVANTAGE
full throttle or high speeds for extended
periods during the first three hours of use. • 32,187 km of field testing • No clutch recalibration
• Thousands of dyno hours • Less wear and tear due to heat
• 18+ months of development • Ensure maximum vehicle performance
(13,000+ design hours) per belt • More time riding, less time wrenching
HALF SHAFT OIL FILTER • 1,500+ vehicle validation hours • Produced in collaboration with
• Collaboration with powertrain powertrain and clutch engineers to & TRAILERING CLEANERS
Check for tears and punctures Change oil filters with every oil and clutch engineers ensure a perfect fit, maximum
in the boot, which can lead to change to provide the best engine performance and ultimate durability
CV joint wear that can protection and keep the engine
contribute to axle failure. operating at peak performance.

FOLLOW RECOMMENDED SERVICE
INTERVALS IN THE OWNER'S MANUAL

MA I NTENANCE SCHEDULE

25 HRS / 400 km 50 HRS / 800 km 100 HRS / 1,600 km 150 HRS / 2,400 km 200 HRS / 3,200 km 250 HRS / 4,023 km 300 HRS / 4,828 km
BREAK-IN 6 12 18 24 30 36 CHECK YOUR
OWNER'S MANUAL
MAINTENANCE FOR ADDITIONAL
MONTHS MONTHS MONTHS MONTHS MONTHS MONTHS RECOMMENDED
SERVICE ITEMS
ENGINE OIL: EXHAUST SYSTEM: ENGINE OIL: BATTERY: ENGINE OIL: ENGINE OIL: ENGINE OIL: AND VEHICLE-
CHANGE INSPECT & CLEAN CHANGE TEST, CLEAN & CHANGE CHANGE CHANGE SPECIFIC TIMING
INSPECT FOR LEAKAGE OR CHECK FLUID LEVEL
GEARCASES: CARBON BUILD UP AT JOINTS DRIVE BELT: IF NECESSARY, REPLACE AS TRANSMISSION FLUID: BATTERY: AIR FILTER:
CHECK OIL LEVEL INSPECT & CLEAN SCREEN INSPECT & ADJUST NEEDED CHANGE TEST, CLEAN & INSPECT & REPLACE
TYPE SPARK ARRESTOR REPLACE AS NEEDED CHECK FLUID LEVEL AS NEEDED
AIR FILTER: DRIVE BELT: GEARCASES: REPLACE AS NEEDED
INSPECT & REPLACE GENERAL SPARK PLUGS: INSPECT & ADJUST CHECK OIL LEVEL GEARCASES:
AS NEEDED LUBRICATION: REPLACE REPLACE AS NEEDED DRIVE BELT: CHECK OIL LEVEL
ALL FITTINGS, BRAKE PADS & FLUID: INSPECT & ADJUST
EXHAUST SYSTEM: PIVOTS, CABLES, ETC. TIRES: INSPECT & CLEAN REPLACE AS NEEDED
INSPECT & CLEAN EXHAUST SYSTEM: INSPECT CONDITION REPLACE AS NEEDED SPARK PLUGS:
INSPECT FOR LEAKAGE OR INSPECT & CLEAN & PRESSURE GENERAL REPLACE
CARBON BUILD UP AT JOINTS DRIVE BELT: INSPECT FOR LEAKAGE OR SPARK PLUGS:
INSPECT & ADJUST CARBON BUILD UP AT JOINTS LUBRICATION:
INSPECT & CLEAN SCREEN REPLACE AS NEEDED EXHAUST SYSTEM: REPLACE ALL FITTINGS, EXHAUST SYSTEM:
TYPE SPARK ARRESTOR INSPECT & CLEAN SCREEN INSPECT & CLEAN PIVOTS, CABLES, ETC. INSPECT & CLEAN
TYPE SPARK ARRESTOR
INSPECT FOR LEAKAGE OR CARBON INSPECT FOR LEAKAGE OR
BUILD UP AT JOINTS EXHAUST SYSTEM: EXHAUST SYSTEM: CARBON BUILD UP AT JOINTS
INSPECT & CLEAN
INSPECT & CLEAN SCREEN TYPE INSPECT FOR LEAKAGE OR INSPECT & CLEAN INSPECT & CLEAN SCREEN
SPARK ARRESTOR CARBON BUILD UP AT JOINTS INSPECT FOR LEAKAGE OR TYPE SPARK ARRESTOR
CARBON BUILD UP AT JOINTS
INSPECT & CLEAN SCREEN TYPE
54 SPARK ARRESTOR INSPECT & CLEAN SCREEN 55
TYPE SPARK ARRESTOR