Page 56 - Catalogo_Acessorios_Sportsman_2021

FOR THE LIFE POLARIS ENGINEERS PARTS THAT PUSH THE LIMITS WITHOUT PARTS & GARAGE

SACRIFICING STRENGTH AND DURABILITY. We build our products so
OF YOUR RIDE anyone with the right tools can maintain their vehicle from their own garage -
and get them back on the trails where they belong.

AIR FILTERS
BATTERIES A clogged air filter can restrict air MAINTENANCE
flow to the engine leading to
MAINTENANCE To ensure a battery maintains its level reduced engine performance,
engine life or catastrophic failure.
of charge when unused for extended
TIP periods of time or during freezing
OIL & LUBRICANTS
weather, the battery should be
connected to a suitable battery charger.
Consult your dealer to ensure the
BREAK-IN PERIOD charger is compatible with your vehicle.
The break-in period for your new DRIVE BELTS MAINTENANCE
Sportsman is the first 25 hours
of operation, or the time it takes Polaris Engineered belts deliver unmatched performance for your off-road
to use the first two tanks of fuel. BRAKE PADS vehicle. Developed and tested on all our engines for all environments and
No single action on your part is conditions. Check your belt for delamination, hour glassing and glazing.
as important as a proper Maintaining and/or replacing brakes BREAK-IN PERIOD
are critical to the safety and
break-in period. Careful functionally of a vehicle. Brake pads • Use lower gear (if available) while varying speeds and avoiding wide open
treatment of a new engine will should be checked for wear and oil throttle for 8-16 km HD PARTS
result in more efficient or grease (petroleum products) • If no low gear is available, vary at moderate speeds while avoiding wide
performance and longer life for contamination and brake discs open throttle for 80 km
should be checked for cracks,
the engine. excessive corrosion or warping.
OUR INVESTMENT YOUR ADVANTAGE
NOTICE: Excessive heat build-up during the • 32,187 km of field testing • No clutch recalibration
first three hours of operation will damage
close-fitted engine parts. Do not operate at • Thousands of dyno hours • Less wear & tear due to heat SERVICE PARTS
full throttle or high speeds for extended • 18+ months of development • Ensure maximum vehicle
periods during the first three hours of use.
(3,000+ design hours) per belt performance
• 1200+ vehicle validation hours • More time riding, less time
• Collaboration with powertrain wrenching
& clutch engineers • Produced in collaboration with
HALF SHAFT OIL FILTERS powertrain and clutch engineers to
ensure a perfect fit, maximum
Change oil filters with every oil performance and ultimate durability BATTERY & LIFTS
Check for tear and punctures in the
boot which can lead to CV joint wear change to provide the best engine
protection and keep the engine
that can contribute to axle failure.
operating at peak performance.
FOLLOW RECOMMENDED SERVICE
INTERVALS IN THE OWNER'S MANUAL & TRAILERING VEHICLE CARE

MAINTENANCE SCHEDULE

25 HRS / 400 km 50 HRS / 800 km 100 HRS / 1600 km 150 HRS / 2400 km 200 HRS / 3200 km 250 HRS / 4023 km 300 HRS / 4828 km
BREAK-IN 6 12 18 24 30 36 CHECK YOUR
OWNER'S MANUAL
MAINTENANCE FOR ADDITIONAL
MONTHS MONTHS MONTHS MONTHS MONTHS MONTHS RECOMMENDED
SERVICE ITEMS
ENGINE OIL: EXHAUST SYSTEM: ENGINE OIL: BATTERY: ENGINE OIL: ENGINE OIL: ENGINE OIL: AND VEHICLE-
CHANGE INSPECT & CLEAN CHANGE TEST, CLEAN, & CHANGE CHANGE CHANGE SPECIFIC TIMING
INSPECT FOR LEAKAGE OR CHECK FLUID LEVEL
GENERAL CARBON BUILD UP AT JOINTS DRIVE BELT: REPLACE AS NEEDED TRANSMISSION FLUID: BATTERY: AIR FILTER:
LUBRICATION: INSPECT & CLEAN SCREEN INSPECT & ADJUST CHANGE TEST, CLEAN, & INSPECT & REPLACE
ALL FITTINGS, PIVOTS, TYPE SPARK ARRESTOR REPLACE AS NEEDED DRIVE BELT: CHECK FLUID LEVEL AS NEEDED
CABLES, ETC. INSPECT & ADJUST GEARCASES: REPLACE AS NEEDED
GENERAL EXHAUST SYSTEM: REPLACE AS NEEDED CHECK OIL LEVEL GEARCASES:
GEARCASES: LUBRICATION: INSPECT & CLEAN DRIVE BELT: CHECK OIL LEVEL
CHECK OIL LEVEL ALL FITTINGS, INSPECT FOR LEAKAGE OR TIRES: BRAKE PADS & FLUID: INSPECT & ADJUST
PIVOTS, CABLES, ETC. CARBON BUILD UP AT JOINTS INSPECT CONDITION INSPECT & CLEAN REPLACE AS NEEDED EXHAUST SYSTEM:
AIR FILTER: & PRESSURE REPLACE AS NEEDED INSPECT & CLEAN
INSPECT & REPLACE DRIVE BELT: INSPECT & CLEAN SCREEN GENERAL INSPECT FOR LEAKAGE OR
TYPE SPARK ARRESTOR
AS NEEDED INSPECT & ADJUST EXHAUST SYSTEM: SPARK PLUGS: LUBRICATION: CARBON BUILD UP AT JOINTS
INSPECT
INSPECT & CLEAN
ALL FITTINGS,
EXHAUST SYSTEM: REPLACE AS NEEDED INSPECT FOR LEAKAGE OR REPLACE AS NEEDED PIVOTS, CABLES, ETC. INSPECT & CLEAN SCREEN
TYPE SPARK ARRESTOR
INSPECT & CLEAN CARBON BUILD UP AT JOINTS
INSPECT FOR LEAKAGE OR EXHAUST SYSTEM: EXHAUST SYSTEM:
CARBON BUILD UP AT JOINTS INSPECT & CLEAN SCREEN INSPECT & CLEAN INSPECT & CLEAN
TYPE SPARK ARRESTOR
INSPECT & CLEAN SCREEN INSPECT FOR LEAKAGE OR INSPECT FOR LEAKAGE OR
TYPE SPARK ARRESTOR CARBON BUILD UP AT JOINTS CARBON BUILD UP AT JOINTS

INSPECT & CLEAN SCREEN TYPE INSPECT & CLEAN SCREEN
SPARK ARRESTOR TYPE SPARK ARRESTOR
54 55