Page 100 - Polaris_Ranger_Catalogo_Acessorios_2019

FOR THE LIFE THE KEY TO KEEPING YOUR POLARIS OFF–ROAD VEHICLE PERFORMING PARTS & GARAGE
®
as well as the day you brought it home is proper maintenance. Items like
belts, filters, and batteries represent only a few of these critical items
OF YOUR RIDE engineered specifically by Polaris. ®

AIR FILTERS DRIVE BELTS OIL & LUBRICANTS
Critical to engine performance and Polaris Engineered ™ belts deliver
reliability. A clogged air filter can unmatched performance for your MAINTENANCE
restrict air flow to the engine leading off-road vehicle. Developed and
to reduced engine performance. Dirt tested on all our engines for all
and debris ingestion can damage the environments and conditions. Check TIP
engine leading to reduced engine life your belt for delamination, hour
or catastrophic failure. Polaris ® glassing and glazing.
recommends changing the vehicle’s MAINTENANCE
air filter at the specified intervals BREAK-IN PERIOD
outlined in the owner’s manual, which
may be shorter if your vehicle is ®
subject to severe conditions. The break-in period for your new RANGER is the
OIL FILTERS first 25 hours of operation, or the time it takes
to use the first two tanks of fuel. No single
Change oil filters with every oil action on your part is as important as a proper
change to provide the best
protection for your engine. Superior break-in period. Careful treatment of a new & TRAILERING VEHICLE CARE
BRAKE PADS engine protection keeps your engine engine will result in more efficient performance
and longer life for the engine. Perform the listed
operating at peak performance. Be
sure to follow the suggested service procedures carefully.
Check your brakes if you are close to intervals for oil/oil filter changes.
the recommended service interval,
hear grinding when applying the NOTICE: Excessive heat build-up during the first three hours
brakes, your vehicle is taking longer of operation will damage close-fitted engine parts. Do not
to stop or if you have to apply more operate at full throttle or high speeds for extended periods
pressure to your pedal to engage the during the first three hours of use.
brakes. Check the brake discs for
signs of cracks, excessive corrosion BATTERIES
or warping.
Never leave a battery unattended
If the brake pads are contaminated during the storage season. To
with oils or grease (petroleum ensure your battery maintains its
products), brake pads have to be level of charge when unused for
discarded and replaced. extended periods of time or during
Discs need to be cleaned with brake freezing weather, the battery
cleaner or alcohol based cleaner only. should be connected to a
BatteryMINDer ® . Be sure to check
for corrosion from the terminals to
the ends of the cables.

MAINTENANCE SCHEDULE

25 HRS/400 km 50 HRS/800 km 100 HRS/1600 km 150 HRS/2400 km 200 HRS/3200 km 350 HRS/4020 km 500 HRS/8045 km
BREAK-IN 6 12 18 24 30 36 CHECK YOUR
OWNER'S MANUAL
MAINTENANCE FOR ADDITIONAL
MONTHS MONTHS MONTHS MONTHS MONTHS MONTHS RECOMMENDED
SERVICE ITEMS
ENGINE OIL: EXHAUST SYSTEM: ENGINE OIL: ENGINE OIL: ENGINE OIL: ENGINE OIL: ENGINE OIL: AND VEHICLE-
CHANGE INSPECT & CLEAN CHANGE CHANGE CHANGE CHANGE CHANGE
INSPECT FOR LEAKAGE OR SPECIFIC TIMING
GENERAL CARBON BUILD UP AT JOINTS DRIVE BELT: BATTERY: BRAKE PADS BATTERY: AIR FILTER:
LUBRICATION: INSPECT & CLEAN SCREEN TYPE INSPECT & ADJUST TEST, CLEAN, & & FLUID: TEST, CLEAN, & INSPECT, CLEAN
ALL FITTINGS, PIVOTS, SPARK ARRESTOR REPLACE AS NEEDED CHECK FLUID LEVEL INSPECT & CLEAN CHECK FLUID LEVEL REPLACE AS NEEDED
CABLES, ETC. REPLACE AS NEEDED REPLACE AS NEEDED REPLACE AS NEEDED
GENERAL TRANSMISSION COOLANT:
AIR FILTER: LUBRICATION: FLUID: DRIVE BELT: SPARK PLUGS: DRIVE BELT: CHECK LEVEL
INSPECT & CLEAN ALL FITTINGS, PIVOTS, CHANGE INSPECT & ADJUST INSPECT INSPECT & ADJUST REPLACE EVERY 2 YEARS
REPLACE AS NEEDED CABLES, ETC. REPLACE AS NEEDED REPLACE AS NEEDED REPLACE AS NEEDED
EXHAUST SYSTEM: GEARCASES:
EXHAUST SYSTEM: DRIVE BELT: INSPECT & CLEAN TIRES: EXHAUST SYSTEM: GENERAL CHECK OIL LEVEL
INSPECT & CLEAN INSPECT & ADJUST INSPECT FOR LEAKAGE OR INSPECT CONDITION INSPECT & CLEAN LUBRICATION:
INSPECT FOR LEAKAGE OR CARBON BUILD UP AT JOINTS & PRESSURE INSPECT FOR LEAKAGE OR ALL FITTINGS, PIVOTS, EXHAUST SYSTEM:
CARBON BUILD UP AT JOINTS REPLACE AS NEEDED CARBON BUILD UP AT JOINTS CABLES, ETC. INSPECT & CLEAN
INSPECT & CLEAN SCREEN
INSPECT & CLEAN SCREEN TYPE SPARK ARRESTOR EXHAUST SYSTEM: INSPECT & CLEAN SCREEN INSPECT FOR LEAKAGE OR
TYPE SPARK ARRESTOR INSPECT & CLEAN TYPE SPARK ARRESTOR EXHAUST SYSTEM: CARBON BUILD UP AT JOINTS
INSPECT FOR LEAKAGE OR INSPECT & CLEAN INSPECT & CLEAN SCREEN
CARBON BUILD UP AT JOINTS INSPECT FOR LEAKAGE OR TYPE SPARK ARRESTOR
CARBON BUILD UP AT JOINTS
INSPECT & CLEAN SCREEN
98 TYPE SPARK ARRESTOR INSPECT & CLEAN SCREEN 99
TYPE SPARK ARRESTOR